J10 on a jku chassis?

Modified FSJ Tech Area
Post Reply

Topic author
Brando0275
Posts: 5
Joined: Sun Aug 20, 2017 7:36 pm

J10 on a jku chassis?

Post by Brando0275 »

I've seen several swaps to different chassis for the j trucks... I would like to use a Jku that I currently have. I can't see where anyone has tried but at a glance it looks like a good fit. The wheel base is within an inch in width and length. I'd imagine that the truck would have a narrower frame so mounts would be fabbed.... any experience with a jk frame/chassis? Anyone know why it wouldn't work?
User avatar

Stuka
Site Admin
Posts: 11789
Joined: Thu May 12, 2011 5:53 pm
Location: CA
Contact:

Re: J10 on a jku chassis?

Post by Stuka »

I have tons of JK experience, having owned a 2dr for 9 years, a new 4dr for, well, 2 days. And I also have my J10.

The wheelbase IS different. A JKU is 116", and a short box J10 is 119". But, JK frames are very easy to length as the center is straight. AEV does this for the double cab Brute conversions. If you just wanted to push out the wheel base, this is not hard either. I know two guys that have pushed their rear axle back a few inches, its not too hard.

The front is where things would get interesting. Frame shapes are quite a bit different, and the JK frame up front is a decent amount narrower as I recall. But thats easy to make up with mounts.
2017 JKU Rubicon
Pevious Jeeps: 1981 J10, 1975 Cherokee, 2008 JK, 2005 KJ, 1989 XJ
User avatar

tgreese
Posts: 7118
Joined: Fri Jun 08, 2012 6:31 am
Location: Medford MA USA

Re: J10 on a jku chassis?

Post by tgreese »

Not knocking it, but it seems kinda backwards to me. Typically it's the sheet metal that melts away from J-trucks, not the chassis. I would expect there to be many more rolling chassis out there than extra bodies. This is certainly the case with CJs, where good chassis way outnumber the available clean bodies ... thus the existence of the MD Juan body kits, and repop fiberglass bodies. The number of existing J-trucks is way lower than CJs, so the availability of chassis may not seem so obvious... except for the number of J-trucks with home-brew flat beds.
Tim Reese
Maine beekeeper's truck: '77 J10 LWB, 258/T15/D20/3.54 bone stock, low options (delete radio), PS/PDB, hubcaps.
Browless and proud: '82 J20 360/T18/NP208/3.73, Destination A/Ts, 7600 GVWR
Copper Polly: '75 CJ-6, 304/T15, PS, BFG KM2s, soft top
GTI without the badges: '95 VW Golf Sport 2000cc 2D
Dual Everything: '15 Chryco Jeep Cherokee KL Trailhawk, ECO Green
Blockchain the vote.

rocklaurence
Vendor
Posts: 2565
Joined: Sat Mar 30, 2013 6:53 am

Re: J10 on a jku chassis?

Post by rocklaurence »

I think its a great idea and you get a much better suspension in the process. I was considering it also and my only regret would be using the JK axles as the originals are heavier. The JK frame and Suspension with the heavier axles would be ideal-IMO..
User avatar

Stuka
Site Admin
Posts: 11789
Joined: Thu May 12, 2011 5:53 pm
Location: CA
Contact:

Re: J10 on a jku chassis?

Post by Stuka »

You can buy weld on brackets for other axles for use on a JK. The rear JK axle is quite strong, especially a Rubicon (8.9" ring gear, D60 pinion size, 32 spline shafts). But the front is definitely weaker on the axle tube front, but has a larger ring gear and is high pinion. Sleeping the axles fixes that.
2017 JKU Rubicon
Pevious Jeeps: 1981 J10, 1975 Cherokee, 2008 JK, 2005 KJ, 1989 XJ
User avatar

tedlovesjeeps71
Posts: 2905
Joined: Fri Jul 22, 2016 4:39 pm

Re: J10 on a jku chassis?

Post by tedlovesjeeps71 »

Interesting thoughts here. I've been bench racing the idea of a TJ unlimited or jk frame swap under my 67 commando. If I were doing a J-truck and just wanted a more modern running gear and comfy suspension, I'd probably just build the J-truck on its frame. Sell the JK and buy long arms/coil overs and drop in a 5.3/6.0. my commando has a very narrow frame so for it, a full swap makes sense. I think.


Sent from my iPhone using Tapatalk

Topic author
Brando0275
Posts: 5
Joined: Sun Aug 20, 2017 7:36 pm

Re: J10 on a jku chassis?

Post by Brando0275 »

Ok... I guess I should give an idea as to my finalized plan. I'd like the updated suspension for a 85 mph highway ride of a trip to the trails. The Jk hits the sweet spot for ride even when lifted with 37's. I'd like the same out of the truck. It's my first fsj so I was looking for the hang-ups that folks have when doing these type swaps. Here is my plan... I have a gen v 5.3 with an 8 speed transmission waiting for an install. I have the grandma JKU 2wd that's super clean waiting to donate the chassis... I want it to look old school but function new...something that functions as good as it looks. My last project turned out pretty good... looking for the next one. My son wants us to build a j truck so he can drive it when he's 16.

ImageImageImageImage


Sent from my iPad using Tapatalk
User avatar

hutcho
Posts: 585
Joined: Wed Apr 25, 2012 11:48 pm
Location: Neosho, MO

Re: J10 on a jku chassis?

Post by hutcho »

I remember seeing one done on the jk frame on the Facebook pages. But I won't even pretend to remember who did it...

Sent from my SAMSUNG-SM-G890A using Tapatalk

Topic author
Brando0275
Posts: 5
Joined: Sun Aug 20, 2017 7:36 pm

Re: J10 on a jku chassis?

Post by Brando0275 »

Well.... I'm in it now. Picked up a couple j10's and am about to start it. We'll see how it goes.


Sent from my iPad using Tapatalk
User avatar

Stuka
Site Admin
Posts: 11789
Joined: Thu May 12, 2011 5:53 pm
Location: CA
Contact:

Re: J10 on a jku chassis?

Post by Stuka »

Cool, look forward to Picts. Should start a build thread on it.
2017 JKU Rubicon
Pevious Jeeps: 1981 J10, 1975 Cherokee, 2008 JK, 2005 KJ, 1989 XJ
User avatar

az chip
Posts: 1433
Joined: Tue Jul 14, 2015 8:59 pm
Location: Mesa, AZ

Re: J10 on a jku chassis?

Post by az chip »

Yeah! Build thread and location.
'81 Cherokee Chief 81 WT Chief/MSD 6/Holley Sniper/ Rusty 4" Spring lift/ Bulltear oil adapter/K&P Engineering Oil Filter/ NP 208/ Serehill Light Harness/KC LED Headlights/ Evil Twin Fab Roof Rack and sliders/ Ross mirror mounts.

Nikkormat
Posts: 3623
Joined: Sun Jun 29, 2014 11:45 pm
Location: Salt Lake City

Re: J10 on a jku chassis?

Post by Nikkormat »

And pics! We all need pictures!
Gabe, "reformed" Jeep hoarder.

Topic author
Brando0275
Posts: 5
Joined: Sun Aug 20, 2017 7:36 pm

Re: J10 on a jku chassis?

Post by Brando0275 »

I will do my best to get it documented... I'm bad about working and forget to take pics.


Sent from my iPad using Tapatalk

Topic author
Brando0275
Posts: 5
Joined: Sun Aug 20, 2017 7:36 pm

Re: J10 on a jku chassis?

Post by Brando0275 »

I will do my best to get it documented... I'm bad about working and forget to take pics.


Sent from my iPad using Tapatalk
User avatar

tedlovesjeeps71
Posts: 2905
Joined: Fri Jul 22, 2016 4:39 pm

Re: J10 on a jku chassis?

Post by tedlovesjeeps71 »

Brando0275 wrote:I will do my best to get it documented... I'm bad about working and forget to take pics.


Sent from my iPad using Tapatalk
I had to train myself to take pics as I went. I'd get well past a project or go to sell it and always forgot about half the things I had done. Image


Sent from my iPhone using Tapatalk
Post Reply