Ad blocker detected: Our website is made possible by displaying online advertisements to our visitors. Please consider supporting us by disabling your ad blocker on our website.
Hi Guys, I've been posting about my 81 J10 build over on jeepfourum but they don't seem too excited. So I thought I'd check you guys out.
I'll...
Last post
In working through this on the Cherokee build I ran across the same problem I decided to go Stainless steel for obvious reasons. I found a reasonably...
While changing the t/stat housing I broke the switch. :( I already have a new one on the way, but do the threads require any sealant? Plumbers tape,...
My wiring is all stock, and clean, I removed all wire loom and tape, examined the wiring and re taped and wire loomed all as original. (found one bad...
Last post
Last time my blinkers went out, I had to buy a quart of blinker fluid to get it fixed.
It's right up there with the impossible to find muffler...
I finally got around to making some interior panels, and the right rear portion (jack cover) seems to be missing a clip or three along the bottom. On...
Last post
Can someone post a picture of the actual clip that goes on the top of the panel. I have a few but they appear to be bent.
Didn't go so well. It seemed this one was too tight of fit into the upper GW shaft. Got it about 3 inches into it, even used my press a little. Ended...
Last post
Just use the entire joint and slip yoke from an XJ.
Then butt weld that to the stock sold part of the GW shaft.
I just had my Motorcraft 2150 carb rebuilt by National Carburetor. When i hooked everything up and cranked it up, it had a ridiculously high idle. i...
Last post
i think i have it fixed, what it ended up being was the choke assembly. But now the fast idle doesn't work. If its not one thing, its another. Oh...
Since looking into replacing the radiator and doing research everybody says watch the fan shroud. Ok so around my mechanical fan I have no shroud. Is...
Last post
Doing some research here. Will I need water pump studs to connect the fan clutch to the pully system? I removed a flex fan with spacer and it was...
Is there anything actually chromed on a waggy? Bumpers I assume are steel, and the window trim also appears to be stainless steel. Late model grills...
During a trip to the local boneyard today, I found a '78 GW with an extremely nice interior. The front seats have some minor creasing, but not even a...
Last post
LOL, nothing quite like being on a steel crew building airplane hangers, having a coworker beating a steel beam into submission when from the other...
Hey All,
I am trying to get the tailgate window finally operational on my 79 wagoneer...I have replaced the motor, wiring, the glass track, all the...
Last post
Do you have your tailgate side channels installed backwards? (upside down) The window lifter channel (part that holds the glass) should not come out...
I order a new readiator and was wondering if I should flush the system? Do I do it when draining the old radiator or after the new one is in? And is...
Last post
If the hose is oily, replace it. Only takes a knife to remove at that point.
I hate to be one of those guys who always starts a new thread for everything, since I know the answer is out there if I look hard enough, but I did a...
Last post
Point being that if it wasn't a CA bound vehicle, they were known to skip stuff. VINS have been known to be traded as well. I would still look for...
So I've been driving 400 Bucks for about 2 weeks now and working all the bugs out. Now for electrical. The temp switch, oil switch and auto choke are...
Last post
Light blue is probably the oil pressure sending unit wire.
Orange is your choke wire and this also powers the carb bowl vent solenoid and your...
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum