Ad blocker detected: Our website is made possible by displaying online advertisements to our visitors. Please consider supporting us by disabling your ad blocker on our website.
I was advised in a previous question about upgrading my alternator that the ammeter bypass is a prudent mod. I search these pages and found some very...
Last post
The link is in this thread.
To use that meter, you need to drill new holes in the circuit board. There's no meter available with the correct...
New to me J10, but it has an aftermarket radio that doesn't work. I'm still waiting on my TSM to be delivered (on order). In the meantime, is the way...
Last post
It comes out easily once you remove the glove box liner. The liner will probably fall apart, BJ’s Offroad sells a nice abs replacement that is easy...
Is there a bellhousing out there that will bolt onto the T176 to allow the use of a stock Jeep 4.0 CPS?
I'm aware of the crank mounted kits....
Last post
I would assume so. AFAIK the 4.0L and 258 flywheels only differ in the addition of the tone ring. Transmission won't care. Starter might be an issue,...
I'm about to start rebuilding my J10 doors and I have question or two. I found this guy on you tube who's gone through the entire process IN DETAIL...
Last post
Thanks for the input. I've got the stock belts but the females both have cracked buckles. That's why the search. I'll research and consider new. I've...
hi, im searching for a pair of Brackets to mount Foglights on Front Bumper of my 82 Wagoneer.
Any Ideas ? Im located in Germany.
thanks Michael :fsj:
Last post
That user was a scammer. They have been deleted. I also edited the two quotes to remove that email address. Should you ever see these, hit the report...
I've been having a shift issues with my TH400 transmission since I bought this '68 J-3500. Today I finally had time to look into it. Figured I either...
Last post
You can use a straight version.
Summitracing , $22. SUM-G110
Good for th350 and th400
Ok here’s a bit of an odd one. So I was scrolling on facebook the other day and on an m715 group I saw someone asking about putting 3rd gen ram 2500...
Last post
The brackets should work, just don’t know if the factory control arms do. You may need to use something like a Johnny Joint to make up for...
Hi All, I've been building my 76 Cherokee and working through the last remaining issues with my new harness based on the '79 wiring diagram. I'd...
Last post
Simplest solution is to resize your pics and let the site host your pics. 800x600 should be ok. Lots of free apps for resizing - I use pixresizer on...
Has anyone retrofitted a combination brake light and cargo light like modern trucks have to where the cargo light mounts? If so what's worked and not...
The original flanged axle d44 in my ‘70 Wagoneer has a lot of play in it. Shifting into drive causes a loud “clunk” and with the drive shaft...
Last post
Ok, so as this area is outboard of the axle tube seal, you will NOT want to seal that area off. Sounds more like it is designed to be open to air, so...
Howdy folks, long time lurker not big poster. I drank the amc koolaid for the last 12 years and after much tinkering, rebuilding and efi'ing, along...
Last post
The full sized GM vans from the late 80s and early 90s with the OD transmissions can donate necessary column shift pieces (indicator) for your setup....
Was wondering what the best place is to pick up 12 volts for my new DUI distributor. Working on a 79 Wagoneer with a 360 engine. The attached pic...
Last post
About my J10 258, the distributor seems worn, lots of vertical play and his the right speed bump at the right speed and angle and it stalls.To renew...
Can anyone point me to information about converting my J10 (1982 258) to an electric fuel pump?
My problem: If the Jeep sits more than a few hours,...
Last post
I used an inline pump from airtex with a low psi output so I didn't need a regulator. My situation involved a 4.0 block though, so there was no mech....
I'm planning on tackling some body rust on my 76 J20 and came upon NOR/AM Body Parts out of Detroit. Specifically the side skins on bed. Anybody have...
Last post
I think that might be where BJ's Offroad gets their panels from.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum