AC fittings and hoses

Area for stock and aftermarket air conditioning.

Topic author
sonoraed
Vendor
Posts: 673
Joined: Sun Apr 07, 2013 7:38 am
Location: Sonora,Ca
Contact:

AC fittings and hoses

Post by sonoraed »

Boring technical stuff but really helps when you need to knowImage

6/8/10 are the common sizes for light trucks and cars




Sent from my iPad using Tapatalk
Last edited by sonoraed on Wed May 20, 2020 6:58 am, edited 1 time in total.

Topic author
sonoraed
Vendor
Posts: 673
Joined: Sun Apr 07, 2013 7:38 am
Location: Sonora,Ca
Contact:

Re: AC fittings and hoses

Post by sonoraed »

Image

Common fitting straight, 45 and 90 degrees of bend,female o ring, beadlock ferrule,aluminum


Sent from my iPad using Tapatalk

Topic author
sonoraed
Vendor
Posts: 673
Joined: Sun Apr 07, 2013 7:38 am
Location: Sonora,Ca
Contact:

Re: AC fittings and hoses

Post by sonoraed »

Image

These fitting are generally used on Sanden compressors with vertical #8 (discharge) and #10 (suction) ports.
Red cap fittings are #8 in 90 and 135 degrees female o ring with high side 134A service port (discharge).
Blue cap fitting is #10 135 degree female o ring with 134A low side service port (suction).


Sent from my iPad using Tapatalk
User avatar

Full Size Jeeper
Posts: 154
Joined: Mon Feb 23, 2015 9:14 pm
Location: Mandeville Louisiana

Re: AC fittings and hoses

Post by Full Size Jeeper »

Ed, just received my hose kit/fittings today.
Image
1978 Jeep Wagoneer

401/turbo 400 transmission Quadra-Trac BW1339 (with Low) 4" Rusty's lift with 31" Summit Mud Dawgs

Mods:
Fuel Tank, Red Holley Electric Fuel Pump, Razor Grill, Rebuilt steering box

Topic author
sonoraed
Vendor
Posts: 673
Joined: Sun Apr 07, 2013 7:38 am
Location: Sonora,Ca
Contact:

Re: AC fittings and hoses

Post by sonoraed »

Image
Image

On the left Male Insert O-Ring MIO
Right Female O-Ring FMO

Imperial Eastman tube bender, different bender for each size tubing, $75-100 each but have found used on EBay


Sent from my iPhone using Tapatalk
User avatar

HeavyMetalThunder_81
Posts: 740
Joined: Sat Mar 17, 2012 5:01 pm
Location: Haze Gray

Re: AC fittings and hoses

Post by HeavyMetalThunder_81 »

Ed, would you be able to build a set of stock AC hoses for a '79? My local AC shop butchered my last set.
-Jonny B.
1979 Cherokee Golden Eagle - UNDER CONSTRUCTION
7" lift, 35x12.5x15
AMC 401 - Pro-FLo 4 FI
NV4500/NWFBB/NP205 - Triple Stick'd
F D44 - 4.10, Eaton E-Locker
R M23 - 4.10, Detroit Locker

1979 Cherokee Chief - Parts
1979 Cherokee Chief - Parts
1979 Wagoneer - Sold
1981 Cherokee Chief - Cubed

Topic author
sonoraed
Vendor
Posts: 673
Joined: Sun Apr 07, 2013 7:38 am
Location: Sonora,Ca
Contact:

Re: AC fittings and hoses

Post by sonoraed »

Yes, but need to know exactly how your truck is equipped, such as type of compressor (i.e. sanden or york on 360 AMC engine), service valves,condenser (oem,aftermarket,o-ring,flare) will you install anew oem drier or relocated aftermarket drier,is the evap the 79 style with flare fittings and externally equalized expansion valve, R12 or 134A
The only way I could recreate a hose set is with detailed input from you or to have your truck here in my shop in central California,otherwise I may also create something that won't work either.

CU4WHLN
Posts: 77
Joined: Sun Dec 14, 2014 7:18 am
Location: Michigan

Re: AC fittings and hoses

Post by CU4WHLN »

Hmm.. Good info.

Now, the "Question" :
I just installed a 2018 GM L 83 and plan to use the stock compressor that came with it. First, what compressor is this? I find no mfg name on it? And - do you have an AC block that would attach to said compressor? Can you make one? I did not get the AC block with the engine.

Reading your post.. it seems I could have you make the lines?
Plan is to use my stock parts.. but want to move the dryer under hood.
I plan to mock up all the hose length and end fittings and have some made. Would ship that to you. Feasible ?

TIA - Jim
It's not YOURS until you BLEED on it !

+ 01 XJ Cream Puff +16 JK Daily Driver + 85 CJ locked and loaded
+ 03 Rubi + 77 Chief 401 + 79 Chero - Madness: Sold

77 Gen V swap http://www.ifsja.org/forums/vb/showthread.php?t=188457
77 401 build: http://www.ifsja.org/forums/vb/showthre ... ief+begins
79 "Madness" build: http://www.ifsja.org/forums/vb/showthre ... ief+begins

Topic author
sonoraed
Vendor
Posts: 673
Joined: Sun Apr 07, 2013 7:38 am
Location: Sonora,Ca
Contact:

Re: AC fittings and hoses

Post by sonoraed »

Just talked to Mark Hugerford at Vintage Air this morning about that very thing, he said the oem compressor (Denso 7SAS17F) is a ecm controlled variable displacement clutchless compressor and won't work with their system, also there is no aftermarket suction/discharge manifold made for that compressor, could modify the original hose by welding a male insert o-ring port.but??!!!
Mark is saying to install a Sanden compressor and they make a kit to convert the oem comp mount to sanden.

CU4WHLN
Posts: 77
Joined: Sun Dec 14, 2014 7:18 am
Location: Michigan

Re: AC fittings and hoses

Post by CU4WHLN »

sonoraed wrote: Thu Jul 09, 2020 11:02 am Just talked to Mark Hugerford at Vintage Air this morning about that very thing, he said the oem compressor (Denso 7SAS17F) is a ecm controlled variable displacement clutchless compressor and won't work with their system, also there is no aftermarket suction/discharge manifold made for that compressor, could modify the original hose by welding a male insert o-ring port.but??!!!
Mark is saying to install a Sanden compressor and they make a kit to convert the oem comp mount to sanden.

Yup - sort of true.. BUT, the hot rod guys feed 12v to the variable inputs and it works like a normal compressor ... Just turn it on and off.
I already changed the acc drive to add a PS pump... Swap time says it will work. They are the one of the few with LT conversion experience.

So, I need to scavenge a AC block for this comp and have it modified? If I do so, can you modify?
I am in the Detroit area.. lots of auto related stuff around here. Was trying to support a Jeep guy....

Here's a video from another place : Watch from the beginning...

https://www.youtube.com/watch?time_cont ... e=emb_logo
It's not YOURS until you BLEED on it !

+ 01 XJ Cream Puff +16 JK Daily Driver + 85 CJ locked and loaded
+ 03 Rubi + 77 Chief 401 + 79 Chero - Madness: Sold

77 Gen V swap http://www.ifsja.org/forums/vb/showthread.php?t=188457
77 401 build: http://www.ifsja.org/forums/vb/showthre ... ief+begins
79 "Madness" build: http://www.ifsja.org/forums/vb/showthre ... ief+begins

Topic author
sonoraed
Vendor
Posts: 673
Joined: Sun Apr 07, 2013 7:38 am
Location: Sonora,Ca
Contact:

Re: AC fittings and hoses

Post by sonoraed »

I stand corrected thought the compressor was clutchless so yes that part of the problem is solved and if you don’t care about the idle up then switch port is not an issue , so only remaining hassle is the suction/ discharge manifold.
I appreciate your support but I’m sure you can find someone close to you to weld aluminum fittings,
I think I have one of those compressors in my inventory ,I’ll take a look at it and see which oem manifold might be worth sacrificing .


Sent from my iPad using Tapatalk

Topic author
sonoraed
Vendor
Posts: 673
Joined: Sun Apr 07, 2013 7:38 am
Location: Sonora,Ca
Contact:

Re: AC fittings and hoses

Post by sonoraed »

Image
Image

Yup caught me with my knickers down!
Had a compressor in stock for the L83, should have looked at first before posting
Vintage Air doesn’t like oem compressors , I guess because of bad experiences with jacked up installs in the field
With the L83 at this time using stock compressor maybe the only way, will take a closer look at comp today and see if something off the shelf might work as a manifold


Sent from my iPhone using Tapatalk

CU4WHLN
Posts: 77
Joined: Sun Dec 14, 2014 7:18 am
Location: Michigan

Re: AC fittings and hoses

Post by CU4WHLN »

Awesome!

Please let me know! I am still finishing my engine swap... AC work is a bit away yet.

Running now, but have to reassemble the Jeep now! lol
It's not YOURS until you BLEED on it !

+ 01 XJ Cream Puff +16 JK Daily Driver + 85 CJ locked and loaded
+ 03 Rubi + 77 Chief 401 + 79 Chero - Madness: Sold

77 Gen V swap http://www.ifsja.org/forums/vb/showthread.php?t=188457
77 401 build: http://www.ifsja.org/forums/vb/showthre ... ief+begins
79 "Madness" build: http://www.ifsja.org/forums/vb/showthre ... ief+begins

Topic author
sonoraed
Vendor
Posts: 673
Joined: Sun Apr 07, 2013 7:38 am
Location: Sonora,Ca
Contact:

Re: AC fittings and hoses

Post by sonoraed »

Spent a bit of time looking for a solution for the manifold and looks the safest thing to do is buy a new set of hoses and cut them up to fit what you have, could also scrounge a up a used set since all you really need is compressor fittings.

Might look at Hawks Motorsport in SC they have a manifold pad that might work ; it’s for a Lsx/ Ls3 but spacing between ports is right.


Sent from my iPad using Tapatalk

CU4WHLN
Posts: 77
Joined: Sun Dec 14, 2014 7:18 am
Location: Michigan

Re: AC fittings and hoses

Post by CU4WHLN »

sonoraed wrote: Tue Jul 14, 2020 9:39 pm Spent a bit of time looking for a solution for the manifold and looks the safest thing to do is buy a new set of hoses and cut them up to fit what you have, could also scrounge a up a used set since all you really need is compressor fittings.

Might look at Hawks Motorsport in SC they have a manifold pad that might work ; it’s for a Lsx/ Ls3 but spacing between ports is right.


Sent from my iPad using Tapatalk
Thanks!

Darn it.. I was hoping somebody had stepped up to this as LT engine swaps are becoming more common.

Oh well . Thanks for investigating !
It's not YOURS until you BLEED on it !

+ 01 XJ Cream Puff +16 JK Daily Driver + 85 CJ locked and loaded
+ 03 Rubi + 77 Chief 401 + 79 Chero - Madness: Sold

77 Gen V swap http://www.ifsja.org/forums/vb/showthread.php?t=188457
77 401 build: http://www.ifsja.org/forums/vb/showthre ... ief+begins
79 "Madness" build: http://www.ifsja.org/forums/vb/showthre ... ief+begins

Topic author
sonoraed
Vendor
Posts: 673
Joined: Sun Apr 07, 2013 7:38 am
Location: Sonora,Ca
Contact:

Re: AC fittings and hoses

Post by sonoraed »

My guess is somebody will or has , just have to find them.

I do have a friend who runs an industrial machine shop he could fab one up in the cnc.


Sent from my iPad using Tapatalk

Scrambler 11
Posts: 3
Joined: Fri Sep 27, 2019 2:28 pm

Re: AC fittings and hoses

Post by Scrambler 11 »

I am working on the a/c setup in my 78 chief with the ls swap 6.2 with stock a/c compressor.
Instead of using the block that bolts onto the compressor there are #8 / #10 conversion fittings made for this purpose. This is what I used Here is a link

https://privatelabelmfg.com/products/pr ... 10s20f-cnc

Also on ebay

https://www.ebay.com/itm/A-C-Compressor ... 3335834103

Topic author
sonoraed
Vendor
Posts: 673
Joined: Sun Apr 07, 2013 7:38 am
Location: Sonora,Ca
Contact:

Re: AC fittings and hoses

Post by sonoraed »

He has a denso 7SAS17 compressor the ports are closer together and has one hold down stud, wish those would work


Sent from my iPad using Tapatalk

Topic author
sonoraed
Vendor
Posts: 673
Joined: Sun Apr 07, 2013 7:38 am
Location: Sonora,Ca
Contact:

Re: AC fittings and hoses

Post by sonoraed »

Image

7SAS17


Sent from my iPad using Tapatalk

Topic author
sonoraed
Vendor
Posts: 673
Joined: Sun Apr 07, 2013 7:38 am
Location: Sonora,Ca
Contact:

Re: AC fittings and hoses

Post by sonoraed »

Image

Cold hose # AA1873 might fit the SAS


Sent from my iPad using Tapatalk
Post Reply